Plumbing and its standards
Much of the plumbing work in populated areas is regulated by government or quasi-government agencies due to the direct impact on the public's health, safety, and welfare. Plumbing installation and repair work on residences and other buildings generally must be done according to plumbing and building codes to protect the inhabitants of the buildings and to ensure safe, quality construction to future buyers. If permits are required for work, plumbing contractors typically secure them from the authorities on behalf of home or building owners.
In the United Kingdom the professional body is the Chartered Institute of Plumbing and Heating Engineering (educational charity status) and it is true that the trade still remains virtually ungoverned; there are no systems in place to monitor or control the activities of unqualified plumbers or those home owners who choose to undertake installation and maintenance works themselves, despite the health and safety issues which arise from such works when they are undertaken incorrectly; see Health Aspects of Plumbing (HAP) published jointly by the World Health Organization (WHO) and the World Plumbing Council (WPC). WPC has subsequently appointed a representative to the World Health Organization to take forward various projects related to Health Aspects of Plumbing.
In the United States, plumbing codes and licensing are generally controlled by state and local governments. At the national level, the Environmental Protection Agency has set guidelines about what constitutes lead-free plumbing fittings and pipes, in order to comply with the Safe Drinking Water Act.
Some widely used Standards in the United States are:
ASME A112.6.3 ? Floor and Trench Drains
ASME A112.6.4 ? Roof, Deck, and Balcony Drains
ASME A112.18.1/CSA B125.1 ? Plumbing Supply Fittings
ASME A112.19.1/CSA B45.2 ? Enameled Cast Iron and Enameled Steel Plumbing Fixtures
ASME A112.19.2/CSA B45.1 ? Ceramic Plumbing Fixtures
Extension of the plumbing in the house
It happens that after some time the use of our water and sewage network we want to expand because of this that We wanted to build a new kitchen or bathroom. On this occasion, employed by our plumbers can evaluate the condition of existing in our home water supply and sewerage. Very often it turns out that it requires the implementation of some repair. Sometimes you need a patency old pipes installed in the house, which has already gathered a lot of hair, soap suds and other substances that inhibit the flow of water. It may also be that Pip such pipes, even using modern methods, does not bring the desired effects and the need to replace old pipes. Expansion of water and sewage networks is toward this very good opportunity.
Wikipedia about elbow pipes
An elbow is a pipe fitting installed between two lengths of pipe or tubing to allow a change of direction, usually a 90° or 45° angle, though 22.5° elbows are also made. The ends may be machined for butt welding, threaded (usually female), or socketed, etc. When the two ends differ in size, the fitting is called a reducing elbow or reducer elbow.
Elbows are categorized based on various design features as below:
Long Radius (LR) Elbows ? radius is 1.5 times the pipe diameter
Short Radius (SR) Elbows ? radius is 1.0 times the pipe diameter
90 Degree Elbow ? where change in direction required is 90°
60 Degree Elbow ? where change in direction required is 60°
45 Degree Elbow ? where change in direction required is 45°
A 90 degree elbow is also called a "90 bend" or "90 ell". It is a fitting which is bent in such a way to produce 90 degree change in the direction of flow in the pipe. It is used to change the direction in piping and is also sometimes called a "quarter bend". A 90 degree elbow attaches readily to plastic, copper, cast iron, steel and lead. It can also attach to rubber with stainless steel clamps. It is available in many materials like silicone, rubber compounds, galvanized steel, etc. The main application of an elbow (90 degree) is to connect hoses to valves, water pressure pumps, and deck drains. These elbows can be made from tough nylon material or NPT thread.
A 45 degree elbow is also called a "45 bend" or "45 ell". It is commonly used in water supply facilities, food industrial pipeline networks, chemical industrial pipeline networks, electronic industrial pipeline networks, air conditioning facility pipeline, agriculture and garden production transporting system, pipeline network for solar energy facility, etc.
Most elbows are available in short radius or long radius variants. The short radius elbows have a center-to-end distance equal to the Nominal Pipe Size (NPS) in inches, while the long radius is 1.5 times the NPS in inches. Short elbows are widely available, and are typically used in pressurized systems.
Long elbows are typically used in low-pressure gravity-fed systems and other applications where low turbulence and minimum deposition of entrained solids are of concern. They are readily available in acrylonitrile butadiene styrene (ABS plastic), polyvinyl chloride (PVC) for DWV, sewage and central vacuums, chlorinated polyvinyl chloride (CPVC) and copper for 1950s to 1960s houses with copper drains.